SONAA

FAQ

Frequently asked questions

Answers about products, installation, maintenance, lead times and warranty for SONAA lines.

Products, sizes and finishes

What colors are available?

SONAA offers an exclusive palette of 10 colors: Natural, White, Black, Gray, Brown, Red, Orange, Green, Blue and Yellow.

Natural is the original color of the plant-based raw material, with no added pigments. Because it is natural, it may show slight tone variations between pieces. Color availability depends on each line.

What is the maximum panel size?

The maximum manufacturing size is 1,000 x 1,000 mm. The shapes and sizes of each line are listed on the line pages.

Can the Modular Ceiling be supplied in 625 x 625 mm or with a Tegular edge?

The SONAA Modular Ceiling is supplied for lay-in systems, in 620 x 620 mm and 1,240 x 620 mm, 20 mm thick, in White and Black.

It has a straight edge for installation on exposed grids. The Tegular (recessed) edge is not part of the standard line.

Can the ceiling be installed on a concealed grid?

Not at the moment. The Modular Ceiling is available only for lay-in systems, with straight edges on exposed grids, in Standard or Slim versions.

Can the panels be installed with tight (dry) joints?

Yes. The Wall & Ceiling line allows tight joints, giving visual continuity and a uniform finish between pieces. All panels in this line are 30 mm thick with chamfered edges that enhance the transition between panels.

Installation

Can the products be installed close to the ceiling or roof?

It depends on the line:

Wall & Ceiling: applied directly to slabs, walls and compatible ceilings.
Clouds: suspended installation, at least 20 cm from the ceiling or slab.
Baffle and Prisms: directly on the ceiling or suspended, depending on the project.
Modular Ceiling: conventional lay-in system, with grids, wall angles, main runners and cross tees available on the market.

Near the roof, check temperature, humidity and environmental exposure, respecting the material’s limits of use.

Can the products be glued directly to the slab?

Yes. The Wall & Ceiling, Clouds and Prisms lines can be installed directly on the slab, with a compatible fixing system and following each product’s recommendations.

The surface must be clean, stable, dry and free of loose particles.

Which adhesive is recommended?

We recommend the high initial tack adhesive foam supplied by SONAA, with an average yield of about 10 m² per tube (varies with the surface). Alternatively, PL500 adhesive, widely available, can be used.

The surface must be clean, dry, stable and free of loose particles or substances that could affect adhesion.

How are cuts and adjustments made?

The products can be cut and adjusted during installation. For simple cuts, use a utility knife with a suitable blade. For greater precision and clean edges, we recommend a table saw with a wood blade.

Cut carefully, without excessive force, to avoid damaging the edges.

Does the product wear when handled? What care is needed?

SONAA products have mechanical strength suited to each application. As an acoustic finishing material, they should be handled with care during transport, storage and installation: avoid impacts, excessive bending and point loads, especially on the edges.

Proper handling does not cause wear or change the product’s color.

Use and maintenance

Can the products be installed near heat sources?

SONAA acoustic absorbers are suitable for environments up to 50 °C. We do not recommend installing them where temperatures exceed this limit or near intense heat sources, especially with direct exposure to thermal radiation.

Can the material deform with heat?

Small dimensional variations may occur with room temperature, without affecting the look of the installed product, as long as the temperature does not exceed 50 °C.

How is cleaning done? Does it collect grease? Can stains be removed?

The surface is fibrous and porous, which is linked to its acoustic performance. For this reason, we do not recommend it for areas frequently exposed to grease, soot, excessive dust or other agents that can impregnate the surface, such as industrial kitchens and some industrial areas.

Under normal use, cleaning is simple: a dry cloth, duster or soft-bristle brush, gently removing surface dust. Avoid harsh chemicals, abrasive materials and excessive rubbing. Stain removal depends on the type and degree of impregnation and cannot be fully guaranteed.

Lead times and warranty

What is the manufacturing lead time?

It varies by line, specification and volume. Under normal conditions, the estimated lead time is 30 to 40 business days, up to 60 business days for larger orders. The final lead time is confirmed with the order.

What is the product warranty?

SONAA products have an 18-month warranty against manufacturing defects, provided the conditions of use, storage, handling and installation in the technical manuals are followed.

The warranty does not cover damage from improper installation, impacts, misuse or exposure to environmental conditions outside the product specifications.

Didn’t find your question?

Talk to us